Vestil WT-2424 & WT-2221 Bedienungsanleitung PDF herunterladen

TILTING WORK TABLE

MODEL WT-2424 & WT-2221

OWNER'S

MANUAL

Revised 09-04 16-126-107

A company dedicated to solving ergonomic and material

handling problems since 1955

Ergonomic Solutions

Caster Installation...........................................2

Parts Identification & Drawing (WT-2424) ......3

Parts Identification & Drawing (WT-2221) ......4

Contents

Warnings and Safety Instructions ................. 1

Receiving Instructions .................................. 1

Operating Instructions .................................. 1

WARNINGS & SAFETY INSTRUCTIONS

Read owner's manual completely before operating unit!

• Keep hands and feet away from all moving parts while

table is in use.

• Do not attempt to adjust the height or tilt angle of the

table while a load is sitting on the platform.

• Never stand or sit on the table.

• Remove load before performing any repairs on the table.

• Use only maintenance parts supplied or approved by

the manufacturer.

• Always engage all wheel brakes when table is not being

moved.

• Never exceed the maximum loading capacity of 300 lbs.

• Load must be evenly distributed on table to ensure

maximum stability.

• Always make sure the height adjustment screw is

securely tightened before a load is applied especially

after table has been raised or lowered.

• Failure to follow these guidelines may result in personal

injury and/or property damage.

RECEIVING INSTRUCTIONS

Every unit is thoroughly tested and inspected prior

to shipment. However, it is possible that the unit may incur

damage during transit. If you see damage when unloading

make a note of it on the SHIPPER RECEIVER.

Remove all packing and strapping material and

inspect for damage. IF DAMAGE IS EVIDENT, FILE A

CLAIM WITH THE CARRIER IMMEDIATELY!

OPERATING INSTRUCTIONS (WT-2424)

1) Position the work table near the desired work area.

2) Lock all four casters.

TILTING WORK TABLE

MODEL WT-2424 & WT-2221

3) Loosen the height adjustment screw and adjust the

work table to the desired height using the handwheel

located on the base frame.

4) Tighten the height adjustment screw.

5) Adjust the tilt angle of the table to the desired position

using the handwheel directly under the table platform.

6) Place the load on table carefully.

OPERATING INSTRUCTIONS (WT-2221)

1) Position the work table near the desired work area.

2) Lock all four casters.

3) Adjust the height to the correct level by star knob

adjustment located on the center column and sliding it

up or down.

4) Loosen the tilt adjustment knob under platform. Tilt

deck to desired angle and retighten.

5) Place the load on the table.

VESTIL MANUFACTURING CORPORATION

2999 North Wayne Street

Angola, IN 46703 USA

Phone (260) 665-7586 • Fax (260) 665-1339

[email protected] • www.vestil.com

1 2 3 4 5 6 ... 11 12

Inhaltsverzeichnis

Seite 1 - OWNER'S

1TILTING WORK TABLEMODEL WT-2424 & WT-2221OWNER'SMANUALRevised 09-04 16-126-107A company dedicated to solving ergonomic and materialhandling

Seite 2

10INSTRUCTIONS POUR LE MONTAGE DES ROULETTESElevez solidement le châssis aussi haut pour que les roulettes puissent glisser sous le bout. Vous verrez

Seite 3

11Légèrement huiler les vis #8 et#12 2 fois par an ou selon lesexigences.IDENTIFICATION DES PIÈCESDESCRIPTION QTÉ.NO. D’ARTICLENO D’INGÉNIEURD/L Dispo

Seite 4 - MODEL WT-2221

Seite 5 - PROPIETARIO

2CASTER INSTALLATION INSTRUCTIONSSecurely prop up one end of the carts frame high enough for the casters to fit underneath that end. You will see four

Seite 6

3Lightly oil screws #8 and #12semiannually or as required.PARTS IDENTIFICATION FOR WT-2424QUANTITY111441111121131142221111A/L Available at local hardw

Seite 7 - IDENTIFICACIÓN DE PARTES

4EXPLODED PARTS LISTMODEL WT-2221ITEM NO.12345678DESCRIPTIONHandle Tilt AdjustingBolt 1/2-13 x 2-3/41/2-13 Nylock NutSwivel CasterBolt 1/4-20 x 3-1/2

Seite 8 - MODELO WT-2221

5INSTRUCCIONES DE SEGURIDAD YADVERTENCIALea el manual del propietario completamente antesde operar le unidad!• Mantenga manos y pies alejados de todas

Seite 9 - D'UTILISATION

6INSTRUCCIONES DE MONTAJE DE LAS RUEDASAsegure y levante un lado del armazón del carro lo suficentemente alto para que las ruedas se puedan poner en e

Seite 10

7Aceite levemente los tornillos#8y #12 semestralmente ósegún se requiera.IDENTIFICACIÓN DE PARTESDESCRIPTIÓN CTD.PARTIDA NO.NO. DE INGENIEROA/L Obteni

Seite 11 - IDENTIFICATION DES PIÈCES

8LISTA DE PARTES EXPLOSIVASMODELO WT-222112345678PARTIDA12345679DESCRIPCIÓNManivela de ajuste de inclinaciónPerno 1.27 cm - 13 x 6.9 cm1.27 cm - 13 Tu

Seite 12 - MODÈLE WT-2221

9AVERTISSEMENTS ET INSTRUCTIONS DESÉCURITÉLire le manuel d'utilisation complètement avant defaire fonctionner l'unité• Écarter mains et pied

Kommentare zu diesen Handbüchern

Keine Kommentare

Vestil WT-2424 & WT-2221 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Ausrüstung Vestil WT-2424 & WT-2221 herunter. Vestil WT-2424 & WT-2221 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Ausrüstung Vestil WT-2424 & WT-2221